
Impact-Resistant Build
Tough ABS shell and clear PC lens resist gravel, vibration, and UV fade.
- ABS housing + PC lens
- Built-in side reflector
- Vibration resistant
CL1600 · JL / JLU FLUSH-MOUNT LED
Low-profile LED tail lights for 2018–2026 Jeep Wrangler JL & JLU.
US factory-halogen models without blind-spot radar (BSM) only.
Explore Lighting
Tucked tight against the quarter panel for a cleaner stance and less trail exposure.
Sharp red alerts and a 30W white reverse beam—no extra backup pods needed.
LIGHTING MODES
Upgrade dim factory halogens for faster brake visibility and a much clearer backup camera at night.

Image unavailable. Please try another option.
Installed look — flush fit with crisp red LED signature.
LOW-PROFILE FIT
Replace protruding factory tail lights with a slim shell that hugs the body and cuts down trail snags.

Far less overhang past the rear quarter panel.

Contoured to fit flush like a custom factory finish.
OUTPUT SPECS
Instant red LED signaling paired with a dedicated white reverse zone.
| Function | Specification |
|---|---|
| Running light | 5.5W Red LED |
| Brake & turn signal | 50W* Red LED |
| Reverse light | 30W · 6000K White |
| Side reflector | Integrated (DOT / SAE) |
*Brake and turn signals share a unified control circuit.

BUILT FOR WRANGLERS
Weather-sealed housing and plug-and-play wiring made for daily roads and rough trails.

Tough ABS shell and clear PC lens resist gravel, vibration, and UV fade.

Sealed tight against downpours, mud spray, trail dust, and washdowns.

Direct factory plug-in with resistors included—skip OBD programmers.

FITMENT CHECK
Fits 2018–2026 US Wrangler JL / JLU with stock halogen lights and no blind-spot radar (triangle icon on the outer lens).
CUSTOM REAR UPGRADE
Get flush trail clearance and a brighter backup view—without spending $500+ on boutique lamps.
Compare Finishes
TWO FINISHES
Same bright LED output. Go Clear for crisp contrast, or Smoked for a blacked-out look.
Previewing Clear Lens — crisp, modern contrast.

Image unavailable. Please try another option.
INSIDE THE LAMP
High-output SMD chips paired with precision optics and weather-tight construction.

REVERSE OPTICS
High-clarity PC optics spread 6000K white light evenly across dark driveways and trails.
High-power SMD LEDs rated up to 6,000 lm peak output in crisp 6000K white.

CONSTRUCTION
Clean internal soldering, IP67 sealing, and UV-resistant PC lenses keep output sharp year-round.
Engineered to resist moisture fogging and lens yellowing with proper gasket installation.

Lights up faster than halogens for extra braking notice.
Regulated circuitry built for a 50,000+ hour lifespan.
Slim housing stays clear of tight brush and obstacles.

IN THE BOX
Everything needed for both sides—no extra brackets or resistors required.
Tip: Mount load resistors to clean metal, away from wiring and plastic trim.
PRODUCT DEMO
Watch the flush body fit and lighting output up close before picking your finish.
Watch on YouTube
SPECS & SUPPORT

Dimensions measure the lamp body. Standard JL/JLU systems run on 12V DC.

CL1600 flush-mount LED tail lights installed on a Wrangler JL.
Yes—for US models with factory halogen tail lights and no BSM radar (Sport, Sport S, Willys, etc.). Not for JK or Gladiator JT.
No. If your stock tail lights are factory LED or show a triangle radar icon (BSM), this kit will not fit.
No. They plug into factory connectors using the included load resistors—no drilling, splicing, or Tazer/JScan needed.
The 30W / 6000K white LED reverse beam is a major jump over dim stock halogens, giving you a much clearer backup camera view.
Both share the exact same LED output. Pick Clear for crisp contrast, or Smoked for a blacked-out look.
Recheck that both factory plugs and load resistors are seated tightly. Still seeing an alert? Message our support team.
Yes—IP67 sealed housings with ABS shells and UV-resistant PC lenses are built for year-round street and trail use.
Covered by a 2-year warranty and 30-day return window under current store policies.
*LED lifespan varies by driving conditions. Confirm your JL/JLU is a US factory-halogen model without BSM before ordering.